SCC Tire Gluing Tool (Large)

Slot Car Corner

$19.99 
SKU: SCCTGT-LG

SCC Tire Gluing Tool (Large)

Let’s face it – gluing slot car tires is a tedious and often messy task.  Depending on the method you use, it’s difficult to ensure the adhesive is spread uniformly across the entire surface where the outer surface of the wheel and inner surface of the tire meet.  The result is an inconsistent bond that is prone to failure under actual race conditions.

The SCC Tire Gluing Tool takes a different approach to gluing tires.  With the SCC Tire Gluing Tool, adhesive is applied uniformly across the entire surface of the wheel.  You can easily see and check to coverage to ensure there are no bare spots.  The tool is designed to stretch a tire slightly so it can be “dropped” onto the wheel.  No more toothpicks or trying to slide the tire across the wheel (and pushing the adhesive off the wheel as you do so).  You get consistent results with better adhesion which yields better performance under race conditions.

The SCC Tire Gluing Tool is available in two (2) sizes:

  • Small – designed for 14mm through 16.00mm wheels (including all popular 15.8mm wheels
  • Large – designed for 16.0mm through 17.5mm wheels (including all popular 17.3mm wheels).  This is the product you are currently viewing. 

Sold individually or as a set of two (2) tools that includes both sizes.

What's included:

  • Tire Gluing Tool
  • Fender Washer
  • Axle stop with M2 set screw

What you'll also need:

  • A 54mm (or longer) 3/32" axle
  • A .035" (0.9mm) hex driver
  • Wheels and tires (of course!)
  • Tire adhesive of your choice

The SCC Tire Gluing Tool works with wheels with or without a center rib.

 

Video

We’ve put together a short video that provides an introduction and tutorial.  Use the following link to view the video.

SCC Tire Gluing Tool Video 

 

FAQ

Q)   What types of adhesive can be used with the SCC Tire Gluing Tool?

A)   There are no restrictions with respect to adhesives; however, if you plan to use a CA glue (super glue) you will need at least 30 seconds working time from the time the glue is applied to the wheel until the glue starts to setup.  The how-to video shows “when” to apply the glue and subsequent steps that must be completed during the adhesive’s working time window.  Be sure to follow the adhesive manufacturer’s instructions for best results and be sure to follow all applicable safety precautions.

Q)  What can I do to make the tire easier to slide down the length of the tool?

A)  You may have to use a little lubricant on the tool to make the tire easier to slide.  If you don’t use a lubricant, the tire will roll on the tool when you go to slide it.  Here are a couple of suggestions:

  • Use a mixture of water with a couple of drops of liquid soap.  Mix the water and soap thoroughly.  Spread a drop or two of the mixture evenly on the outside of the tool.
  • If you are using a silicone based adhesive (e.g. Mega Black), wipe a SMALL amount of silicone spray lubricant over the surface of the tool.

Q)   How do I prevent the adhesive from bonding the wheel to the fender washer included with the SCC Tire Gluing Tool?

A)   As shown in the how-to video, we recommend placing a small circular disc of wax paper between the wheel and fender washer.  This will help prevent any excess glue from bonding the wheel and fender washer together.

Q)   How often should I clean the SCC Tire Gluing Tool?

A)   The SCC Tire Gluing Tool should be cleaned immediately after a tire is glued.  If you are using a silicone based adhesive or other adhesive with a long (minutes/hours) working time, you can usually wipe off any excess adhesive easily with a paper towel.  Be sure to clean the recess in the tool as well.  If you are using an adhesive with a shorter working time such as CA (super glue), carefully clean up as much adhesive that has not setup as possible.  Any adhesive that has setup on the tool or fender washer can be cleaned using acetone (nail polish remover).  Be sure to follow the appropriate safety precautions outlined by the acetone manufacturer.

Q)   When using hubless wheels, how do I access the set screw once the tire has been glued?

A)   You'll need to make a VERY SMALL hole in the tire directly above the set screw access hole in the wheel.  Here are some suggested ways to do this.

  • Use a large needle (e.g. bodkin or similar)
  • Use a small drill bit mounted in a pin vise to "drill" the hole
  • Use a sharp toothpick

Likewise, there are some methods that are NOT recommended

  • Using the tip of your hex driver, screwdriver, etc. (this will have a tendency to create a tear in the tire instead of a hole)
  • Using a tool that is too large (e.g. scrawl or ice pick)
  •  

Q)   The how-to video shows the SCC Tire Gluing Tool being used with a hubless wheel.  Can the tool be used with wheels that have protruding hubs?

A)   Yes - simply rotate the wheel 180 degrees so the back side of the wheel with the protruding hub is mounted on the axle facing toward the inside of the tool.

 

TIPS

If you have any tips on using the SCC Tire Gluing Tool, please let us know.  We will post them here.

"I sung the grub screw in the rim so it will hold in place when putting the tire on but loose enough where I can slide the tire and the rim off the axle. This way once you set the depth of the stopper/washer, you can easily glue multiple rims without haven’t to reset the depth of the rim in the tool."